Skip to main content

An electrician invoice for a 200 A panel upgrade

Electrical work is billed in pieces a homeowner cannot see once the cover plate goes back on: wire pulled through walls, breakers in a panel, an inspector's sign-off. This electrician invoice template is built around making those pieces visible. The sample below is a residential service change from a 100 A to a 200 A panel, billed with a journeyman and an apprentice on separate lines, materials counted by the foot or by the device, the city permit passed through at cost, and the deposit taken for the panel credited at the bottom. Use the blank kit to start your own, then check the licence and permit notes for your state, because in Texas the licence number and a regulator's notice must appear on every invoice.

Updated

Sample electrician invoice on the Contractor template, with invented business, client and prices

Job details

Contractor licence
TECL 12345 (sample)
Permit number
EL-2026-048213 (sample)
Panel and circuits
Main panel, garage east wall; circuits 1 to 32 relabelled
Final inspection
Passed 27 Feb 2026
Shown on the Contractor template. Rendered by the same engine that builds the PDFs Charming sends. Business, client and prices are invented for illustration.

Line items for electrician invoices

Starter line items for electrician invoices, prices left blank
DescriptionQtyUnitPrice
Labour
Journeyman electrician time1hrsLeft blank
Apprentice or helper time1hrsLeft blank
Change order: added circuit or device (describe)1eaLeft blank
Materials
Branch-circuit wire (gauge and type)1ftLeft blank
Circuit breaker (amperage and type)1eaLeft blank
Receptacles, switches and dimmers1eaLeft blank
Boxes, connectors, staples and wire nuts1lotLeft blank
Permit and inspection
Electrical permit fee, passed through at cost1eaLeft blank
Re-inspection after a failed inspection1eaLeft blank
Disposal
Removed panel, fixtures or cable for recycling1lotLeft blank

Prices are left blank on purpose. Use your own rates.

What electrician invoices should include

Contractor licence number (and any notice your regulator requires)
Some states make this part of the invoice itself, not just your van and your adverts. Put it in the footer or header of every invoice so you never have to remember it job by job.
Example: TECL 12345, with the TDLR "Regulated by" statement in the footer
Permit number and inspection result
The permit ties the bill to a public record the homeowner, their insurer or a future buyer can look up. Adding the inspection date shows the work was signed off before you asked for the balance.
Example: Permit EL-2026-048213, final inspection passed 27 Feb
Panel and circuit reference
Months later, "added circuit" means nothing. Naming the panel location and the breaker positions you touched lets the next electrician, or you, trace the work without opening every box.
Example: Main panel, garage east wall; circuits 14 and 16 added
Labour split by crew rank
A journeyman and an apprentice on the same job are worth different rates. Two lines with their own hours stop the client asking why eight hours of helper time cost the same as eight hours of licensed time.
Example: Journeyman 7.5 hrs; apprentice 7.5 hrs
Change-order reference
Extra outlets, a moved fixture or a surprise aluminium branch circuit are the lines that get disputed. Give each one its own line with the date the client approved it.
Example: CO-2: two exterior GFCI receptacles, approved by text 20 Feb

How electrician work is usually billed

Hourly by crew rank, materials by count

Much service and troubleshooting work is billed as time on site at one rate per crew rank, plus materials counted out: wire by the foot, breakers and devices each, and the small consumables as one lot. Time spent hunting a fault is real labour, so list it as "Troubleshooting: tripping kitchen circuit, traced to failed receptacle" rather than burying it inside the repair. Round time the same way on every job and say how in your terms.

Per-device or per-point pricing

Remodel and new-construction work is often priced per point: a set price for each receptacle, switch, light or dedicated circuit, with the wire, box and labour built in. The invoice then reads like the plan: "Recessed light, 6 ea", "Dedicated 20 A circuit, dishwasher, 1 ea". It is easy for a client to check against what they see in the room, but you need a separate line for anything the point price did not cover, such as fishing wire through a finished plaster wall.

Deposit, then balance after inspection

Panel upgrades, EV-charger circuits and generator hookups involve equipment you buy before you start. A common arrangement is a deposit that covers that equipment, then a final invoice once the inspector passes the job, with the deposit shown as a credit. On a large remodel billed in stages, each stage is its own invoice against the contract value; progress invoicing, with a worked example shows how the running totals carry from one invoice to the next.

Change orders as separate lines

Electrical scope moves once walls are open. Bill each approved change as its own line or its own short section, named for what changed, rather than adjusting the original quantities. If the client works through a general contractor or property manager who issued a purchase order, put that number on the invoice too; the PO number guide explains where it goes and why accounts payable needs it.

Rules and good practice

Texas: licence number and the TDLR notice on invoices
Rule

The Texas Department of Licensing and Regulation's compliance guide says an electrical contractor's name, address, phone number and licence number must be on all proposals, invoices and written contracts, and that invoices and written contracts must also carry the statement "Regulated by The Texas Department of Licensing and Regulation" with the department's address, phone numbers and complaints website. The underlying rule is 16 Texas Administrative Code §73.51. The easiest way to comply is to put both in the default footer of every invoice, as the sample does.

Florida: registration or certification number on offers and proposals
Rule

Florida's statute for electrical and alarm system contractors requires the contractor's registration or certification number on each offer of services, business proposal and advertisement. The section does not mention invoices, so the legal requirement is about how you win the job; many Florida contractors print the number on invoices as well so every document matches. Check your county or city for any local rule on top of the state one.

Washington: the permit is bought before the work starts
Rule

Washington's Department of Labor & Industries says electrical work in the state requires a permit and inspection, bought by the electrical contractor or by the owner doing their own work, before any work begins. Some cities issue their own permits instead of L&I. Because the permit exists before the first wire is pulled, its number can go on the deposit invoice as well as the final one.

The electrical code governs the installation, not the invoice

The National Electrical Code and the versions states adopt set how work is installed, not what a bill must say. Naming the breaker type or wire gauge on the invoice is still useful, because it records what went into the wall, but the billing rules come from your licensing board, permit office and tax authority.

General information, not tax or legal advice. Rules vary by place and change; check the current official guidance.

Making electrician invoices in Charming

In Charming each line takes a unit (hrs, ft, ea) and a section label, and on the Contractor template used for this sample, consecutive lines in the same section print under one heading with a subtotal, so Labour, Materials and Permit and inspection add up separately. A deposit received before the invoice goes in its own field and lowers the amount due. Default terms and footer notes are set once per business, which is where a licence number and the Texas regulator statement belong. Other templates, such as Corporate, can show the Unit column and section subtotals once they are switched on in the Template Studio, and the Progress Billing template handles staged remodel invoices against a contract value. The line items above are also a starter kit in the app: on a new invoice with no lines yet, choose Start from a kit, then "Electrician service job" under Trades. Prices start at 0.00 for your own rates.

One tax rate applies to the whole invoice, so if your state taxes materials but not labour you cannot split them on one invoice. There are no estimates or quotes to convert, payments are recorded by hand because clients cannot pay by card through the invoice, and invoices on the Free plan carry a small "Sent with Charming Invoices" line.

Questions

Does an electrician have to put their licence number on an invoice?
It depends on the state. Texas requires the electrical contractor's licence number, name, address and phone number on invoices, plus a statement naming the state regulator. Florida's statute covers offers, proposals and advertising rather than invoices. Elsewhere, check your licensing board's rules; printing the number on every invoice costs nothing and is never wrong.
Should apprentice hours be billed at a lower rate than journeyman hours?
Usually, yes, if your pricing is hourly. Two lines with their own hours and rates are easier to defend than one blended crew rate, because the client can see who did what. If you quote a blended rate instead, say so in the quote and use it consistently, so the invoice never looks like a different pricing method from the one agreed.
How do I put the permit fee on an electrical invoice?
Give the permit its own line with the permit number, and say whether it is passed through at cost or includes your time to apply and schedule the inspection. Keep the receipt from the permit office with the job file. If you charge for the paperwork, a separate line such as "Permit application and inspection scheduling" is clearer than a silent markup.
Who pays for a re-inspection if the job fails inspection?
Decide before the job and write it into your terms. A common approach is that a failure caused by your work is on you, while a failure caused by something outside your scope, such as an existing grounding problem the client declined to fix, is billed as a separate re-inspection line with a short reason the client will recognise.
Can I invoice the panel deposit before the work starts?
Yes. Many electricians send a deposit invoice for the equipment once the quote is accepted, then a final invoice after inspection that lists the full job and subtracts the deposit already paid. The final invoice should show the full value of the work, the deposit as a credit, and the balance, so nobody has to find the first invoice to follow the maths.

Template designs

The Corporate invoice template, shown on a sample invoice

Corporate

Navy band, boxed table and a tax summary — procurement-ready.

The Contractor invoice template, shown on a sample invoice

Contractor

Labour and materials in sections with subtotals, units and total hours, plus a sign-off line.

The Progress Billing invoice template, shown on a sample invoice

Progress Billing

Contract value, % complete, retainage held and balance to complete for staged payments.

Make this invoice with your own details

Add your business, your client and your own rates, then send it to your client as a PDF.